Bike Light Lumens, Lux, and What the Law Actually Requires

Lumens and lux: two numbers, two questions

Let’s run the numbers. LumensThe unit of luminous flux: the total amount of light a source puts out, in every direction. tell you how much light leaves the lamp; luxThe unit of illuminance: the amount of light reaching a surface, measured at one point and at a given distance. tell you how much arrives at one particular spot. The first number describes the lamp, the second what you actually see.

A rough order of magnitude: a 270-lumen light whose beam spreads over about 23 ft wide and 230 ft long (7 by 70 m) gives, on average, around 0.55 lux on the road, so under 1 lux, according to an analysis by a site specializing in bicycle lighting measurements. [1] That has little to do with the figure on a spec sheet: a lux reading taken at the brightest point of a wall 33 ft (10 m) away is not what you’ll see on the pavement as you ride.

The same site points out a classic bias: manufacturers favor high color-temperature LEDs, which give the most lumens and look the brightest, though those figures don’t guarantee you see better. [1] A British guide sums it up: lux and lumens can’t be compared directly, and brightness isn’t the deciding factor in seeing the road or in dazzling other people. [2]

Germany: the Country That Talks in Lux

Germany is the country whose lighting standard everyone quotes, the famous StVZO. Its paragraph 67 describes what a bicycle needs: a white headlight, a red rear lamp, a white reflector at the front, a red category Z reflector at the back, yellow pedal reflectors, and side marking on the wheels (continuous white rings, reflective spokes, or two yellow reflectors per wheel). [3]

The same text allows a dynamo, a battery, or a rechargeable cell to power the lights, so a dynamo isn’t compulsory, contrary to what a recent guide on a specialist site says, which also puts a ceiling of 205 lumens on the front light. [4] We found neither that ceiling nor any lumen figure in paragraph 67; what it does contain is a ban on dazzling other road users.

The figure that turns up in every guide is a minimum of 10 lux at 10 m (33 ft), measured on a wall, with a sharp cut-off beam that keeps most of the light on the road. [4] [2] We didn’t read it in the text of paragraph 67 itself: according to those guides it belongs to type approval, whose trace is the Kraftfahrt-Bundesamt mark, a wavy line, a capital K, and a number. Without that mark, a consumer test says bluntly, the light shouldn’t be fitted to the bike. [5]

Two other rules surprise a visitor: flashing headlights and rear lamps are banned, and paragraph 67, amended in 2013 on the power source, was rewritten in full in 2017. [3] [6] A headlight is mounted roughly 16 to 47 in. (400 to 1,200 mm) above the ground, a rear light roughly 10 to 47 in. (250 to 1,200 mm). [3]

France: a Color, a Mode, No Power Rating

Service-public, the French government’s information site, sums up the French rules: a white or yellow position light at the front, non-dazzling, and a red light at the back, not flashing, at night or by day when visibility is poor. [7] Compulsory lights must be steady; only optional direction indicators may flash. [7] The page gives no visibility distance for lights, and no power threshold.

Reflectors complete the setup: a white one at the front, one or more red ones at the back, orange ones on the wheels (unless the tires are approved reflective ones) and on the pedals. [7] Breaking these rules is punishable by a fine of up to €38, the usual fixed fine being €11. [7] For the full list (bell, helmet, hi-vis vest), our article on required cycling equipment by country covers it.

Great Britain: Flashing Is Allowed, Within Limits

In Great Britain, any cycle used between sunset and sunrise must show a white light at the front, a red light at the back, a red rear reflector, and amber pedal reflectors. [8] The Highway Code says the same: at night, a bicycle must have a white front light and a red rear light, both switched on. [9]

Lights can be steady, flashing, or a mix, but a purely flashing light must flash between 60 and 240 times a minute, at regular intervals, with an intensity of at least 4 candelas. [8] A steady light must meet British Standard BS 6102/3 and carry its marking, even when used in flashing mode; a purely flashing light is exempt. [8] The guides recommend a steady front light wherever street lighting is missing. [8] [9]

United States: Feet of Visibility, State by State

If you ride in the US, here’s the key point: there’s no single national lighting rule. At the federal level, the Consumer Product Safety Commission (CPSC) rule only covers reflectors: a colorless one at the front, a red one at the back, colorless or amber ones on the pedals, and side marking on the wheels. The text says nothing about lamps. [10] Lighting is therefore left to the states, and it’s counted in distance, not in lumens.

In California, a bicycle ridden at night needs a white lamp that lights the way ahead and can be seen from 300 feet (91 m) from the front and sides, plus a red reflector, or a steady or flashing red light with a built-in reflector, visible from 500 feet (152 m) behind. [11] In Washington State, the white front lamp must be seen from 500 feet (152 m), the rear reflector from 600 feet (183 m), and a flashing red LED rear light is allowed in addition to the reflector. [12] In Florida, at night, a white lamp at the front must be visible from 500 feet (152 m), and a red lamp and reflector at the rear from 600 feet (183 m). [13]

The Four Countries at a Glance

What This Changes When You Buy

First habit: look for the beam shape before the power figure. A cut-off beam, as Germany requires, puts most of the light on the road, below the eyes of oncoming drivers; a round beam spreads light in every direction, and a wider, flatter beam dazzles less, according to the same guide. [2] The drawback, noted by the specialist press: this kind of beam leaves little light right in front of the wheel, and it suits a dark trail less well. [4]

Second habit: check the law where you ride, not where the light is sold. In the US, that means your state’s vehicle code, since a box rarely says which distances it meets. A light with a steady, non-flashing, non-dazzling beam meets the French requirements described by Service-public. [7] In Great Britain, a steady light must carry the marking of the British Standard or of an equivalent standard from another country. [8] For battery life and reading spec sheets, our article on headlamp lumens and runtime goes through the FL1 standard.

Third habit: aim the light once it’s fitted, at a wall or a garage door, so that the cut-off falls below a driver’s eye level. That’s what stops you dazzling people, and what the German and French texts both ask for before anything else.

The rule to remember: for bike lights, the shape of the beam and the law where you ride count, not the lumens printed on the box.

Julien de Jurquet

Vans, RVs, biking and calculators

Julien de Jurquet writes for Outfarer about camper vans, RVs, biking, and calculators. He reads manuals cover to cover and never lets a number slide without its unit, so your choices rest on math, not promises.

All their articles