Contents
The notice was published on 17 November 2026 by the safety research team of the Deutscher Alpenverein, the German Alpine Club [1]. We checked it against the English user manual of the avalanche transceiver, or beacon: a unit worn on the body that sends a radio signal and, in search mode, can locate another buried unit and the product page of the Austrian maker, Pieps [2] [3]. This is not a product recall: what owners are asked to do is update the firmware.
What version 1.2 fixes
According to the DAV, users reported Mini IPS units repeatedly showing error code E2 at start-up. The code can be caused by nearby interference when the unit is switched on, and then clear; in a few cases, it was traced to faulty connection points between the Y antenna and the main circuit board, in which case searching was no longer possible [1]. The manual spells out what that means: with a broken Y antenna, the device keeps transmitting but can no longer search correctly [2]. In other words, you can still be found, but you cannot find a buried partner.
Firmware 1.2, the latest version listed by Pieps [3], detects this hardware fault. The unit then shows ‘E2’ and ‘Return for Service’ every time it is switched on; the MARK button clears the message, but it comes back at the next start, so that a faulty unit goes back to the retailer or the manufacturer [1].
How to install the update
- Install the PIEPS app on your phone (iOS or Android) [2].
- Switch on the Mini IPS’s Bluetooth: turn the unit on, then press the MARK button within 2 seconds [1].
- In the app, connect the device and follow the instructions: the DAV says the update takes a few minutes [1].
- Then run the app’s ‘Device Check’, which Pieps recommends at least once a season [2].
Do it at home, not in the car park: the manual warns that the device does not transmit while Bluetooth is activated, and says never to use Bluetooth mode in avalanche terrain [2].
If E2 appears at start-up
For Pieps, an E2 or E4 code means correct operation is no longer guaranteed; the device still starts after you press MARK, so that it remains usable in an emergency. The maker asks you to repeat the self-check outdoors, away from any interference (phones, another transceiver transmitting, metal objects). If the error comes back, the device should no longer be taken on tour, and if ‘Return for Service’ appears, it must be sent in for inspection [2]. Requests go through the Pieps service website given in the manual [2].
| Code | What it means | What Pieps asks you to do |
|---|---|---|
| E2 or E4 | Transmitter or receiver unit: correct operation no longer guaranteed | Repeat the self-check outdoors; if the error comes back, stop taking the device out and contact support [2] |
| E2 and ‘Return for Service’ | Y antenna fault detected by version 1.2 [1] | Send the device in for inspection |
| W4 | A measured value outside the expected range; the device still works | Repeat the self-check away from interference; if the warning appears at every start, take the device back to the retailer |
The Mini IPS reached the shops for the 2025-2026 winter. It weighs 158 g, and the DAV tested it in December 2025 as part of its transceiver review [4]. If you have lent one to a friend or rent them out, pass the word on: your own rescue depends on the devices the others are carrying.
FAQs
Is my Pieps Mini IPS being recalled?
No. The German Alpine Club is asking owners to install firmware 1.2, which detects a Y antenna fault reported on a few units. Only a device that shows ‘E2’ and ‘Return for Service’ after the update needs to be sent to the manufacturer for inspection, through the Pieps service website or your retailer.
How do I know if my Mini IPS is up to date?
Connect it to the PIEPS app, which installs the updates; if you register the device there, you are also told about each new version, according to the manual. The latest version Pieps lists on the Mini IPS product page is 1.2, the one covered by the October 2026 manual. Update at home, because the device does not transmit while Bluetooth is on.
What should I do if E2 appears only once?
Repeat the self-check outdoors, away from your phone, another transmitting transceiver or metal objects: according to Pieps and the DAV, interference at switch-on can be enough to trigger it. If the error comes back, stop taking the device on tour and contact Pieps support.
Sources
- Deutscher Alpenverein, safety research, “Sicherheitshinweis - Wichtiges Softwareupdate für PIEPS Mini IPS”, 17 November 2026 (in German), accessed 18 November 2026. alpenverein.de https://www.alpenverein.de/artikel/sicherheitshinweis-softwareupdate-pieps-mini-ips_12d9d94b-351e-49fc-858c-cc1b754f5e65 ↩
- Pieps GmbH, “PIEPS MINI IPS user manual”, firmware v1.2, October 2026 (PDF), accessed 18 November 2026. pieps.com https://www.pieps.com/wp-content/uploads/2026/10/manual_mini_ips_en.pdf ↩
- Pieps GmbH, “MINI IPS” product page, accessed 18 November 2026. pieps.com https://www.pieps.com/en/product/mini-ips/ ↩
- Deutscher Alpenverein, safety research, “Pieps Mini IPS”, transceiver test, 5 December 2025 (in German), accessed 18 November 2026. alpenverein.de https://www.alpenverein.de/artikel/pieps-mini-ips_836719ac-d8bc-4ee9-97e8-63213e8184ce ↩
Practical guides and news
Articles signed by the editorial team are prepared collectively, from the official texts, standards and studies listed at the end of each article. Every article is dated, and updated when the rules change.



